Abstract
When tunnel boring machines (TBMs) tunnel in extremely hard rock, it is difficult for the cutter to penetrate the rock, resulting in an excessive cutting load, severe wear, and a short lifespan. The rock-breaking mode of synchronous cutting by an abrasive water jet (AWJ) and a disc cutter is expected to improve the rock-breaking performance. To investigate the cutting features of the new method, a synchronous cutting model is established. The results demonstrate that synchronous cutting can significantly enhance the rock-breaking efficiency and reduce the cutting load compared to single-cutter cutting. Moreover, synchronous cutting results in superior rock-breaking effectiveness compared with precutting kerf cutting, attributed to the overlapping of stress waves. The influence of the AWJ kerf depth and the spacing between the disc cutter and the jet on the rock-breaking performance is studied. As the depth of the AWJ kerf increases and the spacing decreases, the cutting load decreases, while the range of rock damage and stress-wave propagation initially increase and then decrease. When the penetration depth of the cutter, kerf depth and spacing are 6 mm, 15 mm, and 30 mm, respectively, the cutting performance of the synchronous cutting is better than that under other conditions.
Highlights
-
A simulation model of the synchronous cutting of granite by an AWJ and a disc cutter is constructed based on the SPH–FEM coupled algorithm.
-
The dynamic process of rock damage and stress-wave propagation is studied for synchronous cutting by an AWJ and a disc cutter.
-
The rock-breaking characteristics of the single-cutter cutting mode, the precutting kerf mode, and the synchronous cutting mode are comprehensively compared.
-
The influence of the AWJ kerf depth and the spacing between the disc cutter and the jet on the rock-breaking performance are investigated.
Similar content being viewed by others
Data Availability
The data that support the findings of this study can be available from the corresponding author upon reasonable request.
References
Afrasiabi N, Rafiee R, Noroozi M (2019) Investigating the effect of discontinuity geometrical parameters on the T-BM performance in hard rock. Tunn Undergr Space Technol 84:326–333. https://doi.org/10.1016/j.tust.2018.11.039
Ai HA, Ahrens TJ (2006) Simulation of dynamic response of granite: a numerical approach of shock-induced damage beneath impact craters. Int J Impact Eng 33:1–10. https://doi.org/10.1016/j.ijimpeng.2006.09.046
Ákos T, Gong QM, Zhao J (2013) Case studies of TBM tunneling performance in rock–soil interface mixed ground. Tunn Underground Space Technol 38:140–150. https://doi.org/10.1016/j.tust.2013.06.001
Cheng JL, Jiang ZH, Han WF et al (2020) Breakage mechanism of hard-rock penetration by TBM disc cutter after high pressure water jet precutting. Eng Fract Mech 240:107320. https://doi.org/10.1016/j.engfracmech.2020.107320
Ciccu R, Grosso B (2014) Improvement of disc cutter performance by water jet assistance. Rock Mech Rock Eng 47:733–744. https://doi.org/10.1007/s00603-013-0433-4
Du M, Wang H, Dong H et al (2020) Numerical research on kerf characteristics of abrasive waterjet machining ba-sed on the SPH-DEM-FEM approach. Int J Adv Manuf Technol 111:3519–3533. https://doi.org/10.1007/s00170-020-06340-4
Erharter GH, Goliasch R et al (2023) On the effect of shield friction in hard rock TBM excavation. Rock Mech Rock Eng. https://doi.org/10.1007/s00603-022-03211-0
Farrokh E (2021) Layout design specifications of hard-rock TBMS disc cutterheads at maximum disc cutter penetration and TBMS advance. Arab J Geosci. https://doi.org/10.1007/s12517-021-08435-y
Ge ZL, Shangguan JM, Zhou Z et al (2023) Investigation of fracture damage and breaking energy consumption of hard rock repeatedly cut by abrasive water jet. Rock Mech Rock Eng. https://doi.org/10.1007/s00603-023-03230-5
Guo B, Xia YM, Cong GQ et al (2017) Numerical simulation of rock fragmentation induced by a single TBM disc cutter close to a side free surface. Int J Rock Mech Min Sci 91:40–48. https://doi.org/10.1016/j.ijrmms.2016.11.004
Hallquist J (2007) LS-DYNA Keyword User’s Manual, Version 971. Livermore Softw Technol Corporation 970:299–800
Hassanpour J, Rostami J, Tarigh S et al (2014) Introduction of an empirical TBM cutter wear prediction model for pyroclastic and mafic igneous rocks; a case history of Karaj water conveyance tunnel. Iran Tunn Undergr Space Technol 43:222–231. https://doi.org/10.1016/j.tust.2014.05.007
Holmquist TJ, Johnson GR, Cook WH (1993) A computational constitutive model for concrete subjected to large strains, high strain rates, and high pressures. In: Proceeding of 14th international symposium on ballistics, Quebec, Canada, pp 591–600
Huang HX, Yao WJ, Li WB et al (2022) Determination of and experimental research on the parameters of the Johnson–Holmquist-II (JH-2) constitutive model for granite. Rock Mech Rock Eng 55:3901–3917. https://doi.org/10.1007/s00603-022-02845-4
Jiang Y, Zeng J, Xu C et al (2022) Experimental study on TBM cutter penetration damage process of highly abrasive hard rock pre-cut by high-pressure water jet. Bull Eng Geol Environ 81:511. https://doi.org/10.1007/s10064-022-03022-1
Kang JF, Li CP, Duan LC et al (2022) An experimental and numerical study on the mechanism of high-voltage electro pulse rock-breaking. Rock Mech Rock Eng 56:2185–2195. https://doi.org/10.1007/s00603-022-03154-6
Kumar N, Shukla M (2012) Finite element analysis of multi-particle impact on erosion in abrasive water jet machining of titanium alloy. J Comput Appl Math 263:4600–4610. https://doi.org/10.1016/j.cam.2012.04.022
Li B, Hu MM, Zhang B et al (2022a) Numerical simulation and experimental studies of rock-breaking methods for pre-grooving-assisted disc cutter. Bull Eng Geol Environ 81:90. https://doi.org/10.1007/s10064-022-02594-2
Li L, Liu ZB, Zhou HY et al (2022b) Prediction of TBM disc cutterhead speed and penetration rate for high-efficiency excavation of hard rock tunnel using CNN-LSTM model with construction big data. Arab J Geosci 15:280. https://doi.org/10.1007/s12517-022-09542-0
Liu SY, Liu ZH, Cui XX et al (2014) Rock breaking of conical cutter with assistance of front and rear water jet. Tunn Undergr Space Technol 42:78–86. https://doi.org/10.1016/j.tust.2014.02.002
Liu XH, Liu SY, Ji HF (2015a) Mechanism of rock-breaking by pick assisted with water jet of different modes. J Mech Sci Technol 29:5359–5368. https://doi.org/10.1007/s12206-015-1137-3
Liu XH, Liu SY, Ji HF (2015b) Numerical research on rock-breaking performance of water jet based on SPH. Powder Technol 286:181–192. https://doi.org/10.1016/j.powtec.2015.07.044
Liu SY, Zhou FY, Li HS et al (2020) Experimental investigation of hard rock-breaking using a conical pick assisted by abrasive water jet. Rock Mech Rock Eng 53:4221–4230. https://doi.org/10.1007/s00603-020-02168-2
Ma XJ, Zhu TX, Fu Y et al (2019) Numerical simulation of rock breaking by abrasive water jet. J Coast Res 93:274–283. https://doi.org/10.2112/SI93-036.1
Mahabadi OK, Cottrell BE, Grasselli G (2010) An example of realistic modelling of rock dynamics problems: FEM/DEM simulation of dynamic brazilian test on barre granite. Rock Mech Rock Eng 43:707–716. https://doi.org/10.1007/s00603-010-0092-7
Mishra S, Chakraborty T (2019) Determination of high-strain-rate stress–strain response of granite for blast analysis of tunnels. J Eng Mech 145:1–23. https://doi.org/10.1061/(ASCE)EM.1943-7889.0001627
Riveiro A, Mejías A, Soto R et al (2016) CO2 laser cutting of natural granite. Opt Laser Technol 76:19–28. https://doi.org/10.1016/j.optlastec.2015.07.018
Rokhy H, Mostofi TM, Ozbakkaloglu T (2022) Calibration of different constitutive material models for vosges sa-ndstone due to its application in rock-cutting processes. J Braz Soc Mech Sci Eng 44:468. https://doi.org/10.1007/s40430-022-03764-9
Salimi A, Rostami J, Moormann C et al (2018) Examining feasibility of developing a rock mass classification for hard rock TBM application using non-linear regression, regression tree and generic programming. Geotech Geol Eng 36:1145–1159. https://doi.org/10.1007/s10706-017-0380-z
Tian XC, Tao TJ, Lou QX et al (2022) Modification and application of limestone HJC constitutive model under the impact load. Lithosphere. https://doi.org/10.2113/2022/6443087
Wan WZ, Yang J, Xu GJ et al (2021) Determination and evaluation of Holmquist-Johnson-Cook constitutive model parameters for ultra-high-performance concrete with steel fibers. Int J Impact Eng. https://doi.org/10.1016/j.ijimpeng.2021.103966
Wang FX, Wang RH, Zhou WD et al (2017) Numerical simulation and experimental verification of the rock dama-ge field under particle water jet impacting. Int J Impact Eng 102:169–179. https://doi.org/10.1016/j.ijimpeng.2016.12.019
Wang J, Yin Y, Luo C (2018) Johnson–Holmquist-II(JH-2) constitutive model for rock materials: parameter determination and application in tunnel smooth blasting. Appl Sci 8:1675. https://doi.org/10.3390/app8091675
Wang FC, Zhou DP, Zhou X et al (2020a) Rock breaking performance of TBM disc cutter assisted by high-pressure water jet. Appl Sci 10:6294. https://doi.org/10.3390/app10186294
Wang ZL, Li YZ, Huang YP (2020b) Determination of JH-2 model parameters and numerical analysis of repeated penetration of granite. Harbin Inst Technol 52:133–142
Wu H, Njock PG, Atangana CJJ, Shen SL (2019) Numerical simulation of spudcan-soil interaction usi-ng an improved smoothed particle hydrodynamics (SPH) method. Mar Struct 66:213–226. https://doi.org/10.1016/j.marstruc.2019.04.007
Yang XF, Li XH, Lu YY (2011) Wear characteristics of the cemented carbide blades in drilling limestone with water jet. Int J Refract Metals Hard Mater 29:320–325. https://doi.org/10.1016/j.ijrmhm.2010.09.007
Yang M, Xia Y, Lin L et al (2020) Optimal design for buckets layout based on muck removal analysis of TBM cutterhead. J Cent South Univ 27(1729):1741. https://doi.org/10.1007/s11771-020-4403-1
Zhang XH, Xia YM, Tan Q et al (2018a) Comparison study on the rock cutting characteristics of disc cutter under free-face-assisted and conventional cutting methods. KSCE J Civ Eng 22:4155–4162. https://doi.org/10.1007/s12205-018-0577-6
Zhang ZX, Wang SF, Huang X (2018b) Analysis on the evolution of rock block behavior during TBM tunnelin-g considering the TBMS–block interaction. Rock Mech Rock Eng 51:2237–2263. https://doi.org/10.1007/s00603-018-1456-7
Zhang JL, Li YC, Zhang YS et al (2020) Using a high-pressure water jet-assisted tunnel boring machine to break rock. Adv Mech Eng 12:1350–1354. https://doi.org/10.1177/1687814020962290
Zheng YL, He L (2021) TBM Tunneling in extremely hard and abrasive rocks: problems, solutions and assisting methods. Cent South Univ 28:454–480. https://doi.org/10.1007/s11771-021-4615-z
Zhou P, Guo J, Sun J et al (2019) Theoretical research and simulation analysis on the cutter spacing of double disc cutters breaking. Rock KSCE J Civ Eng 23:3218–3227. https://doi.org/10.1007/s12205-019-1777-4
Acknowledgements
This work is supported by the Science and Technology Major Project of Ministry of Water Resources of China (SKR-2022029), the China Postdoctoral Science Foundation (No. 2022TQ0378) and the Fundamental Research Funds for the Central Universities of Central South University (No. 2023ZZTS0648). We are grateful to the High Performance Computing Center of Central South University for assistance with the computations.
Funding
This study was funded by the China Postdoctoral Science Foundation (Grant No. 2022TQ0378) and the Fundamental Research Funds for the Central Universities of Central South University (Grant No. 2023ZZTS0648).
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of Interest
The authors declare that they have no conflict of interest.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Yang, G., Zhang, J., Yang, F. et al. Research on the Features of Synchronous Cutting of Granite by Abrasive Water Jet and Disc Cutter. Rock Mech Rock Eng (2024). https://doi.org/10.1007/s00603-024-03770-4
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s00603-024-03770-4