[OT]作为一个SW,怎么修笔记本?

69 views
Skip to first unread message

Holy Li

unread,
Nov 16, 2012, 11:34:10 PM11/16/12
to sh...@googlegroups.com

用了三年的联想笔记本坏了。本来是好的,然后我手贱地开箱清灰,就拔了风扇与硬盘,再装上就成砖了。 现在的现象是:

  • 开机没有明显报警声音;
  • 开机笔记本灯全亮,然后一直保持这个状态;
  • 屏幕是黑的,没有任何反应;
  • 以上状态保持10s左右后会自动关机,然后过5s又自动开机,回到上面的状态……
  • 有没有硬盘,以上现象是一样;

作为一个SW,电脑拿去给别人修多少有点面子挂不住…… 而且怕是很小的一个问题,拿去修被坑。 

所以我决定先自己动手,给点维修建议啊。

Serenade

unread,
Nov 16, 2012, 11:57:04 PM11/16/12
to sh...@googlegroups.com
ifixit,不行就花钱


--
Thanx & Regards,
小溪同学

Ma Xiaojun

unread,
Nov 17, 2012, 12:36:05 AM11/17/12
to sh...@googlegroups.com
SW是什麼?

杨毅涛

unread,
Nov 17, 2012, 2:42:45 AM11/17/12
to sh...@googlegroups.com
再开箱清遍灰。可能某个部件接触不良,全部重新插拔一下。也可能是某个触点被灰尘之类的异物短路了。


2012/11/17 Ma Xiaojun <damag...@gmail.com>
SW是什麼?

--
-- You received this message because you are subscribed to the Google Groups Shanghai Linux User Group group. To post to this group, send email to sh...@googlegroups.com. To unsubscribe from this group, send email to shlug+un...@googlegroups.com. For more options, visit this group at https://groups.google.com/d/forum/shlug?hl=zh-CN



Doloers Haze

unread,
Nov 17, 2012, 3:35:20 AM11/17/12
to sh...@googlegroups.com
BIOS电池松了

2012/11/17, Ma Xiaojun <damag...@gmail.com>:
> SW是什麼?
>
> --
> -- You received this message because you are subscribed to the Google Groups
> Shanghai Linux User Group group. To post to this group, send email to
> sh...@googlegroups.com. To unsubscribe from this group, send email to
> shlug+un...@googlegroups.com. For more options, visit this group at
> https://groups.google.com/d/forum/shlug?hl=zh-CN
>
>
>

--
从我的移动设备发送

chengdong diao

unread,
Nov 17, 2012, 6:32:39 AM11/17/12
to shlug
估计哪里接触不良


2012/11/17 Doloers Haze <doloers....@gmail.com>

Jack Li

unread,
Nov 17, 2012, 7:22:09 AM11/17/12
to sh...@googlegroups.com
再拆一边,看看有什么松了或者没接好。

我今天也拆了我的老笔记本清灰,结果清完装回去多出来四个螺丝。。。
不过能正常启动:)

-Jack

Doloers Haze

unread,
Nov 17, 2012, 7:50:14 AM11/17/12
to sh...@googlegroups.com
某天出现同样的状况,然后把某个螺丝松了半圈就恢复了。不过恢复后BIOS设置复位了

2012/11/17, Jack Li <lij...@gmail.com>:

狗尾草

unread,
Nov 17, 2012, 8:14:43 AM11/17/12
to sh...@googlegroups.com
似乎自检没通过,集成显卡还是独立的?

个人感觉,这种事找售后吧,哈哈,省心。咱不是啥都可以搞的。
同问SW是啥?

--
Best regards,
Hunk Guo
--

Holy Li

unread,
Nov 17, 2012, 8:46:04 AM11/17/12
to sh...@googlegroups.com
独立显卡。
SW不就是Software Engineer吗,泪奔~

2012/11/17 狗尾草 <guo...@gmail.com>

Jianlei Zhang

unread,
Nov 17, 2012, 9:17:25 AM11/17/12
to sh...@googlegroups.com
联想的本子的内部设计还是比较靠谱的,基本上螺丝很少。做为经常帮人拆机清灰的酷毙,我建议你先搞一下内存,硬盘光驱之类的上不上都没关系,起码开机画面会出来。
> --
> -- You received this message because you are subscribed to the Google Groups
> Shanghai Linux User Group group. To post to this group, send email to
> sh...@googlegroups.com. To unsubscribe from this group, send email to
> shlug+un...@googlegroups.com. For more options, visit this group at
> https://groups.google.com/d/forum/shlug?hl=zh-CN
>
>

--
此致

张建雷 敬上

Holy Li

unread,
Nov 17, 2012, 9:20:29 AM11/17/12
to sh...@googlegroups.com
而且按开机键5s,还可以强制关机的。

2012/11/17 Holy Li <holy...@gmail.com>

Holy Li

unread,
Nov 17, 2012, 9:31:21 AM11/17/12
to sh...@googlegroups.com
没有内存条,现象也是一样的……

2012/11/17 Holy Li <holy...@gmail.com>

Holy Li

unread,
Nov 17, 2012, 10:20:23 AM11/17/12
to sh...@googlegroups.com
开机就光盘盒会“噗”的响一下,其他没有任何声音~
光盘盒还可以正常打开、关闭,光盘盒打开关闭时,电脑上的一个灯会相应地闪烁~

2012/11/17 Holy Li <holy...@gmail.com>

qiancheng shen

unread,
Nov 18, 2012, 2:58:30 AM11/18/12
to sh...@googlegroups.com
作为一个同样用联想牌子笔记本的人,我遇到过和你类似的问题,只不过我没有手贱拆开机箱。。。就变成这样了
主要症状是开机灯全亮,屏幕黑,过5s所有灯会闪一下
我当时是拿电吹风吹了笔记本。。。就好了。。。

Lu Guanqun

unread,
Nov 18, 2012, 5:59:38 AM11/18/12
to sh...@googlegroups.com
2012/11/17 Holy Li <holy...@gmail.com>:
> 作为一个SW,电脑拿去给别人修多少有点面子挂不住……

这个很正常,没有什么挂不住的。开车的人也不是每个人都会修车的。

--
Guanqun

sjd....@gmail.com

unread,
Nov 18, 2012, 6:48:36 AM11/18/12
to sh...@googlegroups.com
����ɶѽ�����޾��ޣ����Գ��޵��ԵĻ����޲���ȥ�ҳ��ҵ���


�� 2012��11��18�� 18:59, Lu Guanqun �:
> 2012/11/17 Holy Li <holy...@gmail.com>:
>> ��Ϊһ��SW��������ȥ������޶����е����ӹҲ�ס����
> �������û��ʲô�Ҳ�ס�ġ���������Ҳ����ÿ���˶����޳��ġ�
>

Holy Li

unread,
Nov 18, 2012, 9:23:49 AM11/18/12
to sh...@googlegroups.com
不整了,交给联想客户服务中心了。说主板坏了,要返厂维修,900米没了~
纳闷的是,我只是拆掉风扇与散热器,怎么能把主板弄坏了呢。拆之前还担心静电,特意洗了手的。

2012/11/18 sjd....@gmail.com <sjd....@gmail.com>
这有啥呀,该修就修,电脑城修电脑的还有修不了去找厂家的呢

杨毅涛

unread,
Nov 18, 2012, 1:31:14 PM11/18/12
to sh...@googlegroups.com
哈哈,作为老一辈联想维修中心待过的人,告诉你这样一件事情。
一般这样的情况,都是内部把主板搞坏,发到联想,然后才有钱拿。要不免费的,没有人愿意干。我以前就是因为看不惯这么干,所以和维修站的站长闹僵,然后离开修PC这个行当的。
关于你给钱的事情,主要是看是否在保修期,比如说,输入主板和机器上的序列号码,一般是按出厂三年做保修的。不知道你的过保否。没有过保,那就别人要赚你一笔,如果你的机器都放别人那里了,基本上你现在能拿回来也是坏的了。
这样的事情,不光是联想哦,几乎所有的笔记本维修行业都类似。苹果天才吧没有待过。不知道行情。
还有,拆笔记本是个细活。每颗螺丝都最好分开放。还要记住从哪里拆下来的。另外,操作的时候,要小心再小心。
现在的维修人员,对机器都不怎么样。PC业越来越不景气。所以,没有人认真对待你的机器了。所以,上了二手市场,别人对你的本子修过没有修过非常在意。没有修过的价格可以差一倍哦。

cukimomo521

unread,
Nov 18, 2012, 8:01:48 PM11/18/12
to shlug
哈哈!
我的本本被我拆过N回了!
前几天刚把X200装上触摸屏,过了一把触摸癮,准备还要继续改造。
 
 

cukimomo521
 
发件人: 杨毅涛
发送时间: 2012-11-19 02:31
收件人: shlug
主题: Re: [shlug] [OT]作为一个SW,怎么修笔记本?

沈晓鹏

unread,
Nov 18, 2012, 8:42:12 PM11/18/12
to sh...@googlegroups.com
�� 2012-11-19 9:01, cukimomo521 �:
������
�ҵı������Ҳ��N���ˣ�
ǰ����հ�X200װ�ϴ�����������һ�Ѵ����a��׼����Ҫ������졣
 
 

cukimomo521
 
�����ˣ� ������
����ʱ�䣺 2012-11-19 02:31
�ռ��ˣ� shlug
���⣺ Re: [shlug] [OT]��Ϊһ��SW����ô�ޱʼDZ���
��������Ϊ��һ������ά�����Ĵ����ˣ����������� һ�����顣
һ�����������������ڲ�������㻵���������룬Ȼ�����Ǯ�á�Ҫ����ѵģ�û����Ը��ɡ�����ǰ������Ϊ��������ô�ɣ� ���Ժ�ά��վ��վ���ֽ���Ȼ���뿪��PC����е��ġ�
�������Ǯ�����飬��Ҫ�ǿ��Ƿ��ڱ����ڣ�����˵����������ͻ����ϵ����к��룬һ���ǰ��������������޵ġ���֪����Ĺ� ����û�й��Ǿͱ���Ҫ׬��һ�ʣ������Ļ������ű��������ˣ��������������û���Ҳ�ǻ����ˡ�
��������飬����������Ŷ���������еıʼDZ�ά����ҵ�����ơ�ƻ����Ű�û�д��֪�����顣
���У���ʼDZ��Ǹ�ϸ�ÿ����˿����÷ֿ��š���Ҫ��ס������������ġ����⣬������ʱ��ҪС����С�ġ�
���ڵ�ά����Ա���Ի���������ô��PCҵԽ��Խ���������ԣ�û��������Դ���Ļ����ˡ����ԣ����˶����г������˶��� �ı����޹�û���޹�dz����⡣û���޹�ļ۸���Բ�һ��Ŷ��


�� 2012��11��18�� ����10:23��Holy Li <holy...@gmail.com>д ����
�� ���ˣ���������ͻ����������ˡ�˵���廵�ˣ�Ҫ����ά�ޣ�900��û��~
���Ƶ��ǣ���ֻ�Dz��������ɢ��������ô�ܰ�����Ū�����ء���֮ǰ�����ľ��磬����ϴ���ֵġ�

--
-- You received this message because you are subscribed to the Google Groups Shanghai Linux User Group group. To post to this group, send email to sh...@googlegroups.com. To unsubscribe from this group, send email to shlug+un...@googlegroups.com. For more options, visit this group at https://groups.google.com/d/forum/shlug?hl=zh-CN


--
-- You received this message because you are subscribed to the Google Groups Shanghai Linux User Group group. To post to this group, send email to sh...@googlegroups.com. To unsubscribe from this group, send email to shlug+un...@googlegroups.com. For more options, visit this group at https://groups.google.com/d/forum/shlug?hl=zh-CN
 
 
--
-- You received this message because you are subscribed to the Google Groups Shanghai Linux User Group group. To post to this group, send email to sh...@googlegroups.com. To unsubscribe from this group, send email to shlug+un...@googlegroups.com. For more options, visit this group at https://groups.google.com/d/forum/shlug?hl=zh-CN
 
 
--
-- You received this message because you are subscribed to the Google Groups Shanghai Linux User Group group. To post to this group, send email to sh...@googlegroups.com. To unsubscribe from this group, send email to shlug+un...@googlegroups.com. For more options, visit this group at https://groups.google.com/d/forum/shlug?hl=zh-CN
 
 
ͬ��X200�������ϸ��

qiancheng shen

unread,
Nov 18, 2012, 8:51:41 PM11/18/12
to sh...@googlegroups.com
难怪我说怎么每个笔记本拿过去修。。都说是主板坏。。。原来如此啊。。。!!

Giannini

unread,
Nov 18, 2012, 8:59:52 PM11/18/12
to sh...@googlegroups.com
��Ļ����������ǰ��ȥ�޵ı�������Խ��Խ�� T.T

�� 2012/11/19 9:51, qiancheng shen �:
�ѹ���˵��ôÿ���ʼDZ��ù�ȥ�ޡ�����˵�����廵������ԭ����˰�����������

�� 2012��11��19�� ����2:31�������� <yangy...@gmail.com>���
��������Ϊ��һ������ά�����Ĵ����ˣ�����������һ�����顣
һ�����������������ڲ�������㻵���������룬Ȼ�����Ǯ�á�Ҫ����ѵģ�û����Ը��ɡ�����ǰ������Ϊ��������ô�ɣ� ���Ժ�ά��վ��վ���ֽ���Ȼ���뿪��PC����е��ġ�
�������Ǯ�����飬��Ҫ�ǿ��Ƿ��ڱ����ڣ�����˵����������ͻ����ϵ����к��룬һ���ǰ��������������޵ġ���֪����Ĺ� ����û�й��Ǿͱ���Ҫ׬��һ�ʣ������Ļ������ű��������ˣ��������������û���Ҳ�ǻ����ˡ�
��������飬����������Ŷ���������еıʼDZ�ά����ҵ�����ơ�ƻ����Ű�û�д��֪�����顣
���У���ʼDZ��Ǹ�ϸ�ÿ����˿����÷ֿ��š���Ҫ��ס������������ġ����⣬������ʱ��ҪС����С�ġ�
���ڵ�ά����Ա���Ի���������ô��PCҵԽ��Խ���������ԣ�û��������Դ���Ļ����ˡ����ԣ����˶����г������˶��� �ı����޹�û���޹�dz����⡣û���޹�ļ۸���Բ�һ��Ŷ��
�� 2012��11��18�� ����10:23��Holy Li <holy...@gmail.com>д ����
�����ˣ���������ͻ����������ˡ�˵���廵�ˣ�Ҫ����ά�ޣ�900��û��~
���Ƶ��ǣ���ֻ�Dz��������ɢ��������ô�ܰ�����Ū�����ء���֮ǰ�����ľ��磬����ϴ���ֵġ�

--
-- You received this message because you are subscribed to the Google Groups Shanghai Linux User Group group. To post to this group, send email to sh...@googlegroups.com. To unsubscribe from this group, send email to shlug+un...@googlegroups.com. For more options, visit this group at https://groups.google.com/d/forum/shlug?hl=zh-CN


--
-- You received this message because you are subscribed to the Google Groups Shanghai Linux User Group group. To post to this group, send email to sh...@googlegroups.com. To unsubscribe from this group, send email to shlug+un...@googlegroups.com. For more options, visit this group at https://groups.google.com/d/forum/shlug?hl=zh-CN
 
 
--
-- You received this message because you are subscribed to the Google Groups Shanghai Linux User Group group. To post to this group, send email to sh...@googlegroups.com. To unsubscribe from this group, send email to shlug+un...@googlegroups.com. For more options, visit this group at https://groups.google.com/d/forum/shlug?hl=zh-CN
 
 

Holy Li

unread,
Nov 18, 2012, 11:29:55 PM11/18/12
to sh...@googlegroups.com
这个我是知道的,可是自己又没能力修好,如果学的话花费的时间也不少。
只是希望修好拿回来后,不要越来越坏。

在 2012年11月19日 上午9:59,Giannini <kvm....@gmail.com>写道:
黑幕啊,,,以前拿去修的本,主板越修越坏 T.T


于 2012/11/19 9:51, qiancheng shen 写道:
难怪我说怎么每个笔记本拿过去修。。都说是主板坏。。。原来如此啊。。。!!

在 2012年11月19日 上午2:31,杨毅涛 <yangy...@gmail.com>写道:
哈哈,作为老一辈联想维修中心待过的人,告诉你这样一件事情。
一般这样的情况,都是内部把主板搞坏,发到联想,然后才有钱拿。要不免费的,没有人愿意干。我以前就是因为看不惯这么干, 所以和维修站的站长闹僵,然后离开修PC这个行当的。
关于你给钱的事情,主要是看是否在保修期,比如说,输入主板和机器上的序列号码,一般是按出厂三年做保修的。不知道你的过 保否。没有过保,那就别人要赚你一笔,如果你的机器都放别人那里了,基本上你现在能拿回来也是坏的了。
这样的事情,不光是联想哦,几乎所有的笔记本维修行业都类似。苹果天才吧没有待过。不知道行情。
还有,拆笔记本是个细活。每颗螺丝都最好分开放。还要记住从哪里拆下来的。另外,操作的时候,要小心再小心。
现在的维修人员,对机器都不怎么样。PC业越来越不景气。所以,没有人认真对待你的机器了。所以,上了二手市场,别人对你 的本子修过没有修过非常在意。没有修过的价格可以差一倍哦。


在 2012年11月18日 下午10:23,Holy Li <holy...@gmail.com>写 道:
不整了,交给联想客户服务中心了。说主板坏了,要返厂维修,900米没了~
纳闷的是,我只是拆掉风扇与散热器,怎么能把主板弄坏了呢。拆之前还担心静电,特意洗了手的。

这有啥呀,该修就修,电脑城 修电脑的还有修不了去找厂家的呢


于 2012年11月18日 18:59, Lu Guanqun 写道:
> 2012/11/17 Holy Li <holy...@gmail.com>:
>> 作为一个SW,电脑拿去给别人修多少有点面子挂不住……
> 这个很正常,没有什么挂不住的。开车的人也不是每个人都会修车的。
>

--
-- You received this message because you are subscribed to the Google Groups Shanghai Linux User Group group. To post to this group, send email to sh...@googlegroups.com. To unsubscribe from this group, send email to shlug+un...@googlegroups.com. For more options, visit this group at https://groups.google.com/d/forum/shlug?hl=zh-CN


--
-- You received this message because you are subscribed to the Google Groups Shanghai Linux User Group group. To post to this group, send email to sh...@googlegroups.com. To unsubscribe from this group, send email to shlug+un...@googlegroups.com. For more options, visit this group at https://groups.google.com/d/forum/shlug?hl=zh-CN
 
 
--
-- You received this message because you are subscribed to the Google Groups Shanghai Linux User Group group. To post to this group, send email to sh...@googlegroups.com. To unsubscribe from this group, send email to shlug+un...@googlegroups.com. For more options, visit this group at https://groups.google.com/d/forum/shlug?hl=zh-CN
 
 

--
-- You received this message because you are subscribed to the Google Groups Shanghai Linux User Group group. To post to this group, send email to sh...@googlegroups.com. To unsubscribe from this group, send email to shlug+un...@googlegroups.com. For more options, visit this group at https://groups.google.com/d/forum/shlug?hl=zh-CN
 
 

Risingv

unread,
Nov 18, 2012, 11:49:56 PM11/18/12
to sh...@googlegroups.com


2012/11/18 Lu Guanqun <guanq...@gmail.com>

2012/11/17 Holy Li <holy...@gmail.com>:
> 作为一个SW,电脑拿去给别人修多少有点面子挂不住……

这个很正常,没有什么挂不住的。开车的人也不是每个人都会修车的。
 
你都说了是SW,不是HW。 

这个有什么好纠结的,剑客需要会铸剑吗?果断送修,时间宝贵
 

--
Guanqun

--
-- You received this message because you are subscribed to the Google Groups Shanghai Linux User Group group. To post to this group, send email to sh...@googlegroups.com. To unsubscribe from this group, send email to shlug+un...@googlegroups.com. For more options, visit this group at https://groups.google.com/d/forum/shlug?hl=zh-CN





--
Life is in chaos, keep struggling.
Personal blog: risingv.in

radaiming

unread,
Nov 19, 2012, 12:29:49 AM11/19/12
to sh...@googlegroups.com
我的笔记本我拆了好多次,都是参照网上拆机图小心来的

Jade.Shan

unread,
Nov 19, 2012, 2:17:16 AM11/19/12
to sh...@googlegroups.com
我的HP笔记本两个连续送修了5次。

一开始只是一个USB接口坏了,然后每次送修回来都会有一个新的东西坏掉。

On Mon, Nov 19, 2012 at 12:29:55PM +0800, Holy Li wrote:
> 这个我是知道的,可是自己又没能力修好,如果学的话花费的时间也不少。
> 只是希望修好拿回来后,不要越来越坏。
>

--
CAFE BABE

Holy Li

unread,
Nov 19, 2012, 2:39:11 AM11/19/12
to sh...@googlegroups.com
我周围的朋友也都是这样。
毅涛同学再报下料啊。

p4n.foo

unread,
Nov 19, 2012, 2:44:02 AM11/19/12
to shlug
趁着还在保为什么不享受花钱买的保修业务,非要自己费事拆开修,即使修好了,因为拆机带来保修失效,也是得不偿失的。
 

付鹏
北京航空航天大学沙河校区一公寓北322
Tel :18810662161
 
发件人: Jade.Shan
发送时间: 2012-11-19 15:17
收件人: shlug
主题: Re: [shlug] [OT]作为一个SW,怎么修笔记本?

beck917

unread,
Nov 19, 2012, 3:00:29 AM11/19/12
to sh...@googlegroups.com
x200s同求改造细节...


在 2012年11月19日 上午9:42,沈晓鹏 <doloers....@gmail.com>写道:
于 2012-11-19 9:01, cukimomo521 写道:
哈哈!
我的本本被我拆过N回了!
前几天刚把X200装上触摸屏,过了一把触摸癮,准备还要继续改造。
 
 

cukimomo521
 
发件人: 杨毅涛
发送时间: 2012-11-19 02:31
收件人: shlug
主题: Re: [shlug] [OT]作为一个SW,怎么修笔记本?
哈哈,作为老一辈联想维修中心待过的人,告诉你这样 一件事情。
一般这样的情况,都是内部把主板搞坏,发到联想,然后才有钱拿。要不免费的,没有人愿意干。我以前就是因为看不惯这么干, 所以和维修站的站长闹僵,然后离开修PC这个行当的。
关于你给钱的事情,主要是看是否在保修期,比如说,输入主板和机器上的序列号码,一般是按出厂三年做保修的。不知道你的过 保否。没有过保,那就别人要赚你一笔,如果你的机器都放别人那里了,基本上你现在能拿回来也是坏的了。
这样的事情,不光是联想哦,几乎所有的笔记本维修行业都类似。苹果天才吧没有待过。不知道行情。
还有,拆笔记本是个细活。每颗螺丝都最好分开放。还要记住从哪里拆下来的。另外,操作的时候,要小心再小心。
现在的维修人员,对机器都不怎么样。PC业越来越不景气。所以,没有人认真对待你的机器了。所以,上了二手市场,别人对你 的本子修过没有修过非常在意。没有修过的价格可以差一倍哦。


在 2012年11月18日 下午10:23,Holy Li <holy...@gmail.com>写 道:
不 整了,交给联想客户服务中心了。说主板坏了,要返厂维修,900米没了~
纳闷的是,我只是拆掉风扇与散热器,怎么能把主板弄坏了呢。拆之前还担心静电,特意洗了手的。

这有啥呀,该修就修, 电脑城修电脑的还有修不了去找厂家的呢


于 2012年11月18日 18:59, Lu Guanqun 写道:
> 2012/11/17 Holy Li <holy...@gmail.com>:
>> 作为一个SW,电脑拿去给别人修多少有点面子挂不住……
> 这个很正常,没有什么挂不住的。开车的人也不是每个人都会修车的。
>

--
-- You received this message because you are subscribed to the Google Groups Shanghai Linux User Group group. To post to this group, send email to sh...@googlegroups.com. To unsubscribe from this group, send email to shlug+un...@googlegroups.com. For more options, visit this group at https://groups.google.com/d/forum/shlug?hl=zh-CN


--
-- You received this message because you are subscribed to the Google Groups Shanghai Linux User Group group. To post to this group, send email to sh...@googlegroups.com. To unsubscribe from this group, send email to shlug+un...@googlegroups.com. For more options, visit this group at https://groups.google.com/d/forum/shlug?hl=zh-CN
 
 
--
-- You received this message because you are subscribed to the Google Groups Shanghai Linux User Group group. To post to this group, send email to sh...@googlegroups.com. To unsubscribe from this group, send email to shlug+un...@googlegroups.com. For more options, visit this group at https://groups.google.com/d/forum/shlug?hl=zh-CN
 
 
--
-- You received this message because you are subscribed to the Google Groups Shanghai Linux User Group group. To post to this group, send email to sh...@googlegroups.com. To unsubscribe from this group, send email to shlug+un...@googlegroups.com. For more options, visit this group at https://groups.google.com/d/forum/shlug?hl=zh-CN
 
 
同是X200,求改造细节

Holy Li

unread,
Nov 19, 2012, 3:13:38 AM11/19/12
to sh...@googlegroups.com
已经4年了,已经不在保修了。
否则我何必自己折腾?

cukimomo521

unread,
Nov 19, 2012, 3:37:33 AM11/19/12
to shlug
你好!
X200改造触摸方法:
改造不是很难!我的是改成电阻屏的,电容屏太厚,不方便改造,电阻屏薄,方便改造。
就是需要耐心!
当初,我忘记拍照了,不过,大概写一下改造过程。X200折机,就不说了,网上有N多教程。可以参考一下!
 
 
准备工具:
X200是12.1寸的屏,我事先买了一个 
12寸宽屏 12.1寸触摸屏 超薄 0.5mm,四线电阻触摸屏控制器 ,加上焊接线
 
电烙铁一个,焊锡,焊油,双面胶(薄的),细电线(越细越好,不过,不要太细)4根,这4根线,最好是红,绿。白。黑四个颜色,如果没有也无所谓,只要是好的就行。
再来一个热熔胶(用来固定飞线,和绝缘的),万用表一台,用来测试飞线连接的是否正确。
 
先把买来的屏和触控板用USB接口线接上,插到电脑上,装上驱动,试一下,看看连接的是否正确,触摸屏幕是否好使,可用。并且,也要接线口的顺序用笔记下,一会儿,要飞线
焊接时用。
 
买来的 触摸屏:(如图),实际上屏幕的走线不是在侧面的,是在下面的
 
就是下图这个接线口,买来的是在下面,不是在侧面,在哪一侧,都没有问题,因为我们是另外走线的,不是用这个接线走线的,原因是它太短了。
 
触摸屏的控制卡。一整套,包含控制卡+USB线+延长线+驱动光盘)
 
 
一,开始拆机,网上有教程,把机器拆开,屏幕拆下,开始贴触摸屏
 
屏幕的接法比较简单,拆下来如图(网上找的,我的忘记拍了,大概是一样的)
   
 
 
 
把屏幕拆下来,然后把触摸屏用双面胶粘上,触摸屏的线可以翻到后面,把焊接线接上,
就是这根线,接到屏幕上,由于这线还短,还粗,所以我把它剪掉一断,换上细的线,方便走线,否则太粗
走不了线不说,键盘被顶着还装不下键盘的!由于需要从屏幕上走下4个线,所以,我分了两组走线!,屏幕右侧铁脚走了一根,左侧的铁脚,走了三根。
 
去掉无针这一头,只留下带针的那一头,焊接上细的线,然后开始飞线!
 
 
  
然后是主板走线,走线示意图:
 
 
  
 
把飞过来的线接到控制卡上即可。
 
 
二。处理控制卡
控制卡接线图
 
 
 
控制卡的厚度,不过,还是过于厚了,阻碍了键盘的安装 这里我们需要改造一下,把两头的那个黑色接口与白色接口焊掉
就是
 与    这两个头需要去掉,这样,厚度才最小,能放到硬盘上边,不阻碍键盘的安装
 
焊掉后,直接焊上飞线,飞线的线序如下图。 
 
 
三。控制板飞线到USB接口上
下面是控制板连接到USB内部飞线焊接的点,这样焊接比较简单,但是缺点就是这侧的USB不用使用了,被触摸屏占用了!
所以,有高手的话,可以找一个其它的USB焊接点,不用浪费USB口了!
 
 
 
这4个焊接点需要用万用表 测一上,记不清哪个是Pin1,哪个是Pin4了,
记得好像是,最下面是红色的,然后是白色,绿色,黑色(由下往上) 
 
 
所有的飞线接上后,然后就是把控制板放到硬盘上方,用塑料薄膜包一下绝缘,USB的焊接口用热胶棒封一下,
然后就是装机测试一下,如果好使,就把机器的螺丝装上,就OK了!
 
具体不明白的,可以继续问我!
 
 
Catch7B84.jpg
Catch5243.jpg
Catch1C47.jpg
Catch1E7F.jpg
Catch2673.jpg
Catch3312.jpg
CatchD06F.jpg
Catch153C.jpg
CatchC3E8.jpg
Catch6935.jpg
Catch.jpg
Catch2962.jpg
Catch1EAD.jpg
CatchD21A.jpg
Catch7BDE.jpg
Catch1D57.jpg
CatchBA33.jpg

唐嘉祺

unread,
Nov 19, 2012, 3:55:47 AM11/19/12
to sh...@googlegroups.com
好犀利。。我周末正在想这个事儿。查了一下教程都没你写的详细。有时间可以DIY一下了。


 
 

--
CatchC3E8.jpg
CatchBA33.jpg
Catch1EAD.jpg
Catch1C47.jpg
Catch3312.jpg
Catch2962.jpg
Catch2673.jpg
Catch7BDE.jpg
Catch6935.jpg
Catch.jpg
CatchD06F.jpg
Catch153C.jpg
CatchD21A.jpg
Catch5243.jpg
Catch7B84.jpg
Catch1E7F.jpg
Catch1D57.jpg

杨毅涛

unread,
Nov 19, 2012, 5:45:58 AM11/19/12
to sh...@googlegroups.com
强悍,就是不知道笔记本要触摸屏干吗的飘过。
CatchD06F.jpg
CatchBA33.jpg
Catch2673.jpg
Catch.jpg
Catch1C47.jpg
Catch1D57.jpg
Catch6935.jpg
Catch7BDE.jpg
Catch1E7F.jpg
CatchC3E8.jpg
Catch2962.jpg
Catch1EAD.jpg
CatchD21A.jpg
Catch5243.jpg
Catch3312.jpg
Catch7B84.jpg
Catch153C.jpg

杨毅涛

unread,
Nov 19, 2012, 6:00:13 AM11/19/12
to sh...@googlegroups.com
总之别人是要赚点钱了。估计拆开一下,不会坏什么大部件。可能别人维修站,拆开,捣鼓下,就可以开机启动了。
说实在的,现在的机器,越来越耐折腾。静电,损坏的几率很小。开机用打火机里面拆出来的电打火  电主板。都不一定能电的坏。
还有可能是拆卸的时候,把某个部件掰坏的几率会大一些。也有可能是弄入异物之类。或者什么东西没有装好,短路,以及把某个连线接反(这事伤害比较大,极有可能烧掉很多东西)。当然,只要外观没有什么异常,在保的机器都可以保修,稍微超几天也是有办法的,比如发票时间。
所以,比较佩服装触摸屏的兄弟的动手能力和勇气。

不过,既然成事实,往好的方向去想把。笔记本最佳使用寿命,3年保修本,两年半多一点出手换新本吧,留几个月保修最好。最好没有拆修过(如果连升级都没有弄过最好)。这样最保值。

Doloers Haze

unread,
Nov 19, 2012, 6:29:21 AM11/19/12
to sh...@googlegroups.com
赞,不过不影响显示效果么?

在 12-11-19,杨毅涛<yangy...@gmail.com> 写道:


> 强悍,就是不知道笔记本要触摸屏干吗的飘过。
>
>
> 在 2012年11月19日 下午4:55,唐嘉祺 <tjq9...@gmail.com>写道:
>
>> 好犀利。。我周末正在想这个事儿。查了一下教程都没你写的详细。有时间可以DIY一下了。
>>
>>
>> 在 2012年11月19日 下午4:37,cukimomo521 <cukim...@gmail.com>写道:
>>

>> **


>>> 你好!
>>> X200改造触摸方法:
>>> 改造不是很难!我的是改成电阻屏的,电容屏太厚,不方便改造,电阻屏薄,方便改造。
>>> 就是需要耐心!
>>> 当初,我忘记拍照了,不过,大概写一下改造过程。X200折机,就不说了,网上有N多教程。可以参考一下!
>>>
>>>
>>> 准备工具:
>>> X200是12.1寸的屏,我事先买了一个
>>> 12寸宽屏 12.1寸触摸屏 超薄 0.5mm,四线电阻触摸屏控制器 ,加上焊接线
>>>
>>>
>>> 电烙铁一个,焊锡,焊油,双面胶(薄的),细电线(越细越好,不过,不要太细)4根,这4根线,最好是红,绿。白。黑四个颜色,如果没有也无所谓,只要是好的就行。

>>> 再来一个热熔胶*棒*(用来固定飞线,和绝缘的),万用表一台,用来测试飞线连接的是否正确。


>>>
>>>
>>> 先把买来的屏和触控板用USB接口线接上,插到电脑上,装上驱动,试一下,看看连接的是否正确,触摸屏幕是否好使,可用。并且,也要接线口的顺序用笔记下,一会儿,要飞线
>>> 焊接时用。
>>>
>>> 买来的 触摸屏:(如图),实际上屏幕的走线不是在侧面的,是在下面的
>>>

>>> 就是下图这个接线口,买来的是在下面,不是在侧面,在哪一侧,都没有问题,因为我们是另外走线的,不是用这个接线走线的,原因是它太短了。
>>>

>>> 触摸屏的控制卡。一整套,包含*(**控制卡+USB线+延长线+驱动光盘)*


>>>
>>>
>>> 一,开始拆机,网上有教程,把机器拆开,屏幕拆下,开始贴触摸屏
>>>
>>> 屏幕的接法比较简单,拆下来如图(网上找的,我的忘记拍了,大概是一样的)
>>>
>>>
>>>

>>> 把屏幕拆下来,然后把触摸屏用双面胶粘上,触摸屏的线可以翻到后面,把焊接线接上,
>>> 就是这根线,接到屏幕上,由于这线还短,还粗,所以我把它剪掉一断,换上细的线,方便走线,否则太粗
>>> 走不了线不说,键盘被顶着还装不下键盘的!由于需要从屏幕上走下4个线,所以,我分了两组走线!,屏幕右侧铁脚走了一根,左侧的铁脚,走了三根。
>>>

>>> 去掉无针这一头,只留下带针的那一头,焊接上细的线,然后开始飞线!
>>>
>>>
>>> 然后是主板走线,走线示意图:
>>>
>>>
>>>
>>> 把飞过来的线接到控制卡上即可。
>>>
>>>
>>> 二。处理控制卡
>>> 控制卡接线图


>>>
>>>
>>>
>>> 控制卡的厚度,不过,还是过于厚了,阻碍了键盘的安装 这里我们需要改造一下,把两头的那个黑色接口与白色接口焊掉
>>> 就是

>>> 与 这两个头需要去掉,这样,厚度才最小,能放到硬盘上边,不阻碍键盘的安装
>>>
>>> 焊掉后,直接焊上飞线,飞线的线序如下图。
>>>
>>>


>>> 三。控制板飞线到USB接口上
>>> 下面是控制板连接到USB内部飞线焊接的点,这样焊接比较简单,但是缺点就是这侧的USB不用使用了,被触摸屏占用了!
>>> 所以,有高手的话,可以找一个其它的USB焊接点,不用浪费USB口了!
>>>
>>>
>>>

>>> 这4个焊接点需要用万用表 测一上,记不清哪个是Pin1,哪个是Pin4了,


>>> 记得好像是,最下面是红色的,然后是白色,绿色,黑色(由下往上)
>>>
>>>

>>> 所有的飞线接上后,然后就是把控制板放到硬盘上方,用塑料薄膜包一下绝缘,USB的焊接口用热胶棒封一下,
>>> 然后就是装机测试一下,如果好使,就把机器的螺丝装上,就OK了!
>>>
>>> 具体不明白的,可以继续问我!
>>>
>>>
>>>
>>> --
>>> -- You received this message because you are subscribed to the Google
>>> Groups Shanghai Linux User Group group. To post to this group, send email
>>> to sh...@googlegroups.com. To unsubscribe from this group, send email to
>>> shlug+un...@googlegroups.com. For more options, visit this group
>>> at https://groups.google.com/d/forum/shlug?hl=zh-CN
>>>
>>>
>>>
>>
>> --
>> -- You received this message because you are subscribed to the Google
>> Groups Shanghai Linux User Group group. To post to this group, send email
>> to sh...@googlegroups.com. To unsubscribe from this group, send email to
>> shlug+un...@googlegroups.com. For more options, visit this group at
>> https://groups.google.com/d/forum/shlug?hl=zh-CN
>>
>>
>>
>
> --
> -- You received this message because you are subscribed to the Google Groups
> Shanghai Linux User Group group. To post to this group, send email to
> sh...@googlegroups.com. To unsubscribe from this group, send email to
> shlug+un...@googlegroups.com. For more options, visit this group at
> https://groups.google.com/d/forum/shlug?hl=zh-CN
>
>
>

--
从我的移动设备发送

SuperCat

unread,
Nov 19, 2012, 6:49:31 AM11/19/12
to sh...@googlegroups.com
电阻屏其实没啥意思,虽然精度很高甚至都能拿来画图,但是不能玩多点触摸…………
不过DIY一下倒是不错

2012/11/19 Doloers Haze <doloers....@gmail.com>

albert zhang

unread,
Nov 19, 2012, 7:32:39 AM11/19/12
to shlug
看看红外屏
 
 
2012-11-19
Best Regards
 
Albert Zhang
 
发件人: SuperCat
发送时间: 2012-11-19 19:49
收件人: shlug
主题: Re: [shlug] 公布一下X200改造触摸过程。当初忘记截取图了,所以在网上找了一些图。做了描述。

cukimomo521

unread,
Nov 19, 2012, 9:42:47 AM11/19/12
to shlug
你好!
红外屏,还是厚啊!本本安不了,不过台式机可以试着装一个,
 
安装完电阻屏,屏幕有些发白,没办法,触摸屏的效果不是很透亮,
 
装完以后,我也不知道做什么啊!反正没事就是点着屏幕玩,不过,在win8系统里可,倒是可以玩切水果,
 
 

cukimomo521
 
发件人: albert zhang
发送时间: 2012-11-19 20:32
收件人: shlug
主题: 回复: Re: [shlug] 公布一下X200改造触摸过程。当初忘记截取图了,所以在网上找了一些图。做了描述。

gavin geng

unread,
Nov 19, 2012, 10:02:51 AM11/19/12
to sh...@googlegroups.com

      之前用hp 6531s,自己修,把底部的螺丝全卸下来了,前面就拆了个防尘的壳,就啥也拆不了了,没辙啊,散热不行,肯定就不能用啊,于是找小区门口维修的小伙,他说,没问题,最多1.5小时搞定,结果,拆完就一个钟头,MD,把所有的都拆完了,清洗灰尘,又装了1.5小时,整整3钟头!那个线路复杂的啊......

Ma Xiaojun

unread,
Nov 19, 2012, 6:29:52 PM11/19/12
to sh...@googlegroups.com
GNOME Shell能支持嗎?

cukimomo521

unread,
Nov 19, 2012, 8:09:12 PM11/19/12
to shlug
可以的,记得,好像是有linux驱动的!
 

cukimomo521
 
發件人: Ma Xiaojun
發送時間: 2012-11-20 07:29
收件人: shlug
主題: Re: 回复: [shlug] 公布一下X200改造触摸过程。当初忘记截取图了,所以在网上找了一些图。做了描述。
GNOME Shell能支持嗎?

cukimomo521

unread,
Nov 19, 2012, 8:12:58 PM11/19/12
to shlug
 
Supported Operating Systems
  • MS-DOS, Windows 95/98/2000/CE/ME/2000NT, OS/2, MAC, Linux etc
 
 
OS Support 1. Windows 95/ 98/ ME/ NT4/ 2000/ XP/ XP Tablet PC edition
  2. Windows CE 2.12/ 3.0/ .net/ 5.0
  3. Linux (up to Kernel 2.6)
  4. MS-DOS: support display resolution: 320x200, 640x200,
    640x350, 640x480, 800x600, 1024x768 and 1280x1024
  5. iMac 9.0/ OS X
 
 
 
 

cukimomo521
 
發件人: Ma Xiaojun
發送時間: 2012-11-20 07:29
收件人: shlug
主題: Re: 回复: [shlug] 公布一下X200改造触摸过程。当初忘记截取图了,所以在网上找了一些图。做了描述。
GNOME Shell能支持嗎?
Catch.jpg

sjd....@gmail.com

unread,
Nov 19, 2012, 9:01:06 PM11/19/12
to sh...@googlegroups.com
û�����ػ��������ѽ

�� 2012��11��19�� 18:45, ������ �:
ǿ�������Dz�֪���ʼDZ�Ҫ�����������Ʈ��


�� 2012��11��19�� ����4:55���Ƽ��� <tjq9...@gmail.com>д ����
��Ϭ������ĩ����������¶����һ�½̶̳�û��д����ϸ����ʱ�����DIYһ���ˡ�


�� 2012��11��19�� ����4:37��cukimomo521 <cukim...@gmail.com>д ����

��ã�
X200���촥��������
���첻�Ǻ��ѣ��ҵ��Ǹ� �ɵ������ģ�������̫�񣬲�������죬����������������졣
������Ҫ���ģ�
����������������ˣ��� ����дһ�¸����̡��أ������ۻ�Ͳ�˵�ˣ������Уζ�̡̳����Բο�һ�£�
 
 
׼�����ߣ�
�أ������ǣ���.1��� ��������������һ����
12����� 12.1�紥���� ���� 0.5mm�����ߵ��败�����������������Ϻ�����
 
������һ�������� ���ͣ�˫�潺�����ģ���ϸ���ߣ�ԽϸԽ�ã�����Ҫ̫ϸ�������⣴���ߣ�����Ǻ죬 �̡��ס����ĸ���ɫ�����û��Ҳ����ν��ֻҪ�Ǻõľ��С�
����һ���� �۽����������̶����ߣ��;�Ե�ģ������ñ�һ̨���� �����Է������ӵ��Ƿ���ȷ��
 
�Ȱ����������ʹ��ذ��ãգӣ½ӿ��� ���ϣ��嵽�����ϣ�װ������һ�£��������ӵ��Ƿ���ȷ��������Ļ�Ƿ��ʹ�����á����ң�Ҳ Ҫ���߿ڵ�˳���ñʼ��£�һ���Ҫ����
����ʱ�á�
 
�����ġ�������������ͼ����ʵ������ Ļ�����߲����ڲ���ģ����������
 
������ͼ������߿ڣ��������������棬������ ���棬����һ�࣬��û�����⣬��Ϊ�������������ߵģ�����������������ߵģ�ԭ������̫���ˡ�
 
�� �����Ŀ��ƿ���һ���ף��������ƿ�+USB��+�ӳ���+����̣�
 
 
һ����ʼ��������н̳̣��ѻ����𿪣���Ļ���£���ʼ������
 
��Ļ�Ľӷ��Ƚϼ򵥣��� ������ͼ�������ҵģ��ҵ�������ˣ������һ��ģ�
������
 
 
 
����Ļ��������Ȼ��Ѵ� ������˫�潺ճ�ϣ����������߿��Է������棬�Ѻ����߽��ϣ�
��������ߣ��ӵ���Ļ �ϣ��������߻��̣����֣������Ұ������һ�ϣ�����ϸ���ߣ��������ߣ�����̫��
�߲����߲�˵�����̱����Ż�װ���¼� �̵ģ�������Ҫ����Ļ�����£����ߣ����ԣ��ҷ����������ߣ�����Ļ�Ҳ��������һ�������� �ţ��������
 
ȥ��������һͷ��ֻ���´������һͷ���� ����ϸ���ߣ�Ȼ��ʼ���ߣ�
 
 
����
Ȼ�����������ߣ�����ʾ��ͼ��
 
 
����
 
�ѷɹ������߽ӵ����ƿ��ϼ��ɡ�
 
 
��������� �ƿ�
���ƿ����� ͼ
 
 
 
���ƿ��ĺ�ȣ����� �ǹ��ں��ˣ��谭�˼��̵İ�װ������������Ҫ����һ�£�����ͷ���Ǹ���ɫ�ӿ��� ��ɫ�ӿں���
����
�� �롡���� ��������ͷ��Ҫȥ���������Ȳ���С���ܷŵ�Ӳ���ϱߣ����谭���̵İ�װ
 
������ֱ�Ӻ��Ϸ��ߣ����ߵ��������� ͼ����
 
 
����� ����ߵ��գӣ½ӿ���
�����ǿ��ư����ӵ��գӣ��ڲ����ߺ��ӵ� �㣬����ӱȽϼ򵥣�����ȱ��������ģգӣ²���ʹ���ˣ���������ռ���ˣ�
���ԣ��и��ֵĻ���������һ������� �գӣº��ӵ㣬�����˷ѣգӣ¿��ˣ�
 
 
 
�⣴�����ӵ���Ҫ������ �?��һ�ϣ��Dz����ĸ��ǣ�in�����ĸ��ǣ�in���ˣ�
�ǵú����ǣ��������Ǻ� ɫ�ģ�Ȼ���ǰ�ɫ����ɫ����ɫ���������ϣ���
 
 
���еķ��߽��Ϻ�Ȼ����ǰѿ��ư�ŵ�Ӳ�� �Ϸ��������ϱ�Ĥ��һ�¾�Ե���գӣµĺ��ӿ����Ƚ�����һ�£�
Ȼ�����װ�����һ�£�����ʹ���Ͱѻ����� ��˿װ�ϣ��ͣϣ��ˣ�
 
���岻���׵ģ����Լ������ң�
 
 
--
-- You received this message because you are subscribed to the Google Groups Shanghai Linux User Group group. To post to this group, send email to sh...@googlegroups.com. To unsubscribe from this group, send email to shlug+un...@googlegroups.com. For more options, visit this group at https://groups.google.com/d/forum/shlug?hl=zh-CN
 
 
--
-- You received this message because you are subscribed to the Google Groups Shanghai Linux User Group group. To post to this group, send email to sh...@googlegroups.com. To unsubscribe from this group, send email to shlug+un...@googlegroups.com. For more options, visit this group at https://groups.google.com/d/forum/shlug?hl=zh-CN
 
 

Rivsen

unread,
Nov 19, 2012, 9:09:27 PM11/19/12
to sh...@googlegroups.com
试试华硕的 变形金刚 带底座的,就知道笔记本装触摸屏能干啥啦~

话说我现在用苹果的机器总想上手去划啊点啊的 -_-


在 2012年11月20日 上午10:01,sjd....@gmail.com <sjd....@gmail.com>写道:
没事来回划拉着玩儿呀


于 2012年11月19日 18:45, 杨毅涛 写道:
强悍,就是不知道笔记本要触摸屏干吗的飘过。


在 2012年11月19日 下午4:55,唐嘉祺 <tjq9...@gmail.com>写 道:
好犀利。。我周末正在想这个事儿。查了一下教程都没你写的详细。有时间可以DIY一下了。


在 2012年11月19日 下午4:37,cukimomo521 <cukim...@gmail.com>写 道:

你好!
X200改造触摸方法:
改造不是很难!我的是改 成电阻屏的,电容屏太厚,不方便改造,电阻屏薄,方便改造。
就是需要耐心!
当初,我忘记拍照了,不 过,大概写一下改造过程。X200折机,就不说了,网上有N多教程。可以参考一下!
 
 
准备工具:
X200是12.1寸的 屏,我事先买了一个 
12寸宽屏 12.1寸触摸屏 超薄 0.5mm,四线电阻触摸屏控制器 ,加上焊接线
 
电烙铁一个,焊锡, 焊油,双面胶(薄的),细电线(越细越好,不过,不要太细)4根,这4根线,最好是红, 绿。白。黑四个颜色,如果没有也无所谓,只要是好的就行。
再来一个热 熔胶(用来固定飞线,和绝缘的),万用表一台,用 来测试飞线连接的是否正确。
 
先把买来的屏和触控板用USB接口线 接上,插到电脑上,装上驱动,试一下,看看连接的是否正确,触摸屏幕是否好使,可用。并且,也 要接线口的顺序用笔记下,一会儿,要飞线
焊接时用。
 
买来的 触摸屏:(如图),实际上屏 幕的走线不是在侧面的,是在下面的
 
就是下图这个接线口,买来的是在下面,不是在 侧面,在哪一侧,都没有问题,因为我们是另外走线的,不是用这个接线走线的,原因是它太短了。
 
触 摸屏的控制卡。一整套,包含控制卡+USB线+延长线+驱动光盘)
 
 
一,开始拆机,网上有教程,把机器拆开,屏幕拆下,开始贴触摸屏
 
屏幕的接法比较简单,拆 下来如图(网上找的,我的忘记拍了,大概是一样的)
   
 
 
 
把屏幕拆下来,然后把触 摸屏用双面胶粘上,触摸屏的线可以翻到后面,把焊接线接上,
就是这根线,接到屏幕 上,由于这线还短,还粗,所以我把它剪掉一断,换上细的线,方便走线,否则太粗
走不了线不说,键盘被顶着还装不下键 盘的!由于需要从屏幕上走下4个线,所以,我分了两组走线!,屏幕右侧铁脚走了一根,左侧的铁 脚,走了三根。
 
去掉无针这一头,只留下带针的那一头,焊 接上细的线,然后开始飞线!
 
 
  
然后是主板走线,走线示意图:
 
 
  
 
把飞过来的线接到控制卡上即可。
 
 
二。处理控 制卡
控制卡接线 图
 
 
 
控制卡的厚度,不过,还 是过于厚了,阻碍了键盘的安装 这里我们需要改造一下,把两头的那个黑色接口与 白色接口焊掉
就是
  与     这两个头需要去掉,这样,厚度才最小,能放到硬盘上边,不阻碍键盘的安装
 
焊掉后,直接焊上飞线,飞线的线序如下 图。 
 
 
三。控制 板飞线到USB接口上
下面是控制板连接到USB内部飞线焊接的 点,这样焊接比较简单,但是缺点就是这侧的USB不用使用了,被触摸屏占用了!
所以,有高手的话,可以找一个其它的 USB焊接点,不用浪费USB口了!
 
 
 
这4个焊接点需要用万用 表 测一上,记不清哪个是Pin1,哪个是Pin4了,
记得好像是,最下面是红 色的,然后是白色,绿色,黑色(由下往上) 
 
 
所有的飞线接上后,然后就是把控制板放到硬盘 上方,用塑料薄膜包一下绝缘,USB的焊接口用热胶棒封一下,
然后就是装机测试一下,如果好使,就把机器的 螺丝装上,就OK了!
 
具体不明白的,可以继续问我!
 
 
--
-- You received this message because you are subscribed to the Google Groups Shanghai Linux User Group group. To post to this group, send email to sh...@googlegroups.com. To unsubscribe from this group, send email to shlug+un...@googlegroups.com. For more options, visit this group at https://groups.google.com/d/forum/shlug?hl=zh-CN
 
 
--
-- You received this message because you are subscribed to the Google Groups Shanghai Linux User Group group. To post to this group, send email to sh...@googlegroups.com. To unsubscribe from this group, send email to shlug+un...@googlegroups.com. For more options, visit this group at https://groups.google.com/d/forum/shlug?hl=zh-CN
 
 
--
-- You received this message because you are subscribed to the Google Groups Shanghai Linux User Group group. To post to this group, send email to sh...@googlegroups.com. To unsubscribe from this group, send email to shlug+un...@googlegroups.com. For more options, visit this group at https://groups.google.com/d/forum/shlug?hl=zh-CN
 
 

杨毅涛

unread,
Nov 19, 2012, 9:54:32 PM11/19/12
to sh...@googlegroups.com
HP还有DELL等美系厂商,还有苹果。都有详尽的维修手册可以下载。网上搜索一下,或者上英文版的页面上,可以下载下来。然后读遍手册,照手册拆装就可以了。
以前在HP金牌修大幅面打印机的时候养成的习惯,那个玩艺,你要不看手册,或者没有读过手册。你永远拆不开。读过,指定位置上几颗螺丝一拆就开了,没有读过,卸上几十颗螺丝,外壳都打不开很正常的。哈哈哈。
后来发现,很多厂商都有维修手册的,网上也有很多拆装资料,最好先看看再动手。每款机器的型号都不一样。你不可能全都知道。但是看过维修手册就基本上全能了。
联想维修站内部,还有详尽的机器BOM单,就是机器采用的什么品牌型号的部件。如果没有备件了,可以从市面上采购或者寻找替换维修。不过,这个玩艺是保密的,要有一定级别才可以看到的。正常情况下,网上不会找到的。

lo.yu.linux

unread,
Nov 19, 2012, 11:39:45 PM11/19/12
to sh...@googlegroups.com
话说没事拆自己的本本,螺丝是越拆越少;最悲剧的是自己的打印机,装好以后,剩下十来颗螺丝躺地上...

sjd....@gmail.com

unread,
Nov 19, 2012, 11:52:34 PM11/19/12
to sh...@googlegroups.com
�ϻ����Dz��ǵ����Ĥѽ

�� 2012��11��20�� 10:09, Rivsen �:
���Ի�˶�� ���ν�� �����ģ���֪���ʼDZ�װ�������ܸ�ɶ����

��˵��������ƻ��Ļ�����������ȥ�����㰡�� -_-


�� 2012��11��20�� ����10:01��sjd....@gmail.com <sjd....@gmail.com>д ����
û�����ػ��������ѽ

�� 2012��11��19�� 18:45, ������ �:
ǿ�������Dz�֪���ʼDZ�Ҫ�����������Ʈ��
�� 2012��11��19�� ����4:55���Ƽ��� <tjq9...@gmail.com>д ����
��Ϭ������ĩ����������¶����һ�½̶̳�û��д����ϸ����ʱ�����DIYһ���ˡ�
�� 2012��11��19�� ����4:37��cukimomo521 <cukim...@gmail.com>д ����
�� �ã�
X200 ���촥��������
�� �첻�Ǻ��ѣ��ҵ��Ǹ� �ɵ������ģ�������̫�񣬲�������죬����������������졣
�� ����Ҫ���ģ�
�� ��������������ˣ��� ����дһ�¸����̡��أ������ۻ�Ͳ�˵�ˣ������Уζ�̡̳����Բο�һ�£�
 
 
׼ �����ߣ�
�أ����� �ǣ���.1��� ��������������һ����
12����� 12.1�紥���� ���� 0.5mm�����ߵ��败������ �����������Ϻ�����
 
������һ�������� ���ͣ�˫�潺�����ģ���ϸ���ߣ�ԽϸԽ�ã�����Ҫ̫ϸ�������⣴���ߣ�����Ǻ죬 �̡��ס����ĸ���ɫ�����û��Ҳ����ν��ֻҪ�Ǻõľ��С�
����һ���� �۽����������̶����ߣ� �;�Ե�ģ������ñ�һ̨���� �����Է������ӵ��Ƿ���ȷ��
 
�Ȱ����������� ���ذ��ãգӣ½ӿ��� ���ϣ��嵽�����ϣ�װ������һ�£��������ӵ��Ƿ���ȷ��������Ļ�Ƿ��ʹ�����á����ң�Ҳ Ҫ���߿ڵ�˳���ñʼ��£�һ���Ҫ����
���ԣ��и��ֵ� ����������һ������� �գӣº��ӵ㣬�����˷ѣգӣ¿��ˣ�
 
 
 
�� �������ӵ���Ҫ������ �?��һ�ϣ��Dz����ĸ��ǣ�in�����ĸ��ǣ�in���ˣ�
�� �ú����ǣ��������Ǻ� ɫ�ģ�Ȼ���ǰ�ɫ����ɫ����ɫ���������ϣ���
 
 
���еķ��߽��Ϻ� Ȼ����ǰѿ��ư�ŵ�Ӳ�� �Ϸ��������ϱ�Ĥ��һ�¾�Ե���գӣµĺ��ӿ����Ƚ�����һ�£�
Ȼ�����װ�����һ�£� ����ʹ���Ͱѻ����� ��˿װ�ϣ��ͣϣ��ˣ�
 
���岻���׵ģ����� �������ң�
 
 
--
-- You received this message because you are subscribed to the Google Groups Shanghai Linux User Group group. To post to this group, send email to sh...@googlegroups.com. To unsubscribe from this group, send email to shlug+un...@googlegroups.com. For more options, visit this group at https://groups.google.com/d/forum/shlug?hl=zh-CN
 
 
--
-- You received this message because you are subscribed to the Google Groups Shanghai Linux User Group group. To post to this group, send email to sh...@googlegroups.com. To unsubscribe from this group, send email to shlug+un...@googlegroups.com. For more options, visit this group at https://groups.google.com/d/forum/shlug?hl=zh-CN
 
 
--
-- You received this message because you are subscribed to the Google Groups Shanghai Linux User Group group. To post to this group, send email to sh...@googlegroups.com. To unsubscribe from this group, send email to shlug+un...@googlegroups.com. For more options, visit this group at https://groups.google.com/d/forum/shlug?hl=zh-CN
 
 
--
-- You received this message because you are subscribed to the Google Groups Shanghai Linux User Group group. To post to this group, send email to sh...@googlegroups.com. To unsubscribe from this group, send email to shlug+un...@googlegroups.com. For more options, visit this group at https://groups.google.com/d/forum/shlug?hl=zh-CN
 
 

Wizard

unread,
Nov 20, 2012, 6:56:48 PM11/20/12
to shlug
老杨拆过这么多东西啊


在 2012年11月20日 上午10:54,杨毅涛 <yangy...@gmail.com>写道:



--
Wizard

杨毅涛

unread,
Nov 21, 2012, 12:04:51 AM11/21/12
to sh...@googlegroups.com
曾经的工作就是拆拉。哈哈哈。
现在我自己的笔记本,如果有问题,都是自己拆开先看故障,基本上判断没有什么问题。然后直接带到维修中心去,让他们给我保修我自己判断出故障的零部件就可以了。当然,某些维修中心接待的人水平很弱的那种,死活不相信,非要自己测。结果研究很久以后,比我研究的时间多几倍,结论是我判断没有错。乖乖的给我订零部件换上。
Reply all
Reply to author
Forward
0 new messages